Minecraft How to Make a Garbage Disposal
These proficient, illustrated instructions will guide you step-by-pace through the procedure of installing a garbage disposal, including the expanse under the sink and the garbage disposal, removing the erstwhile disposer, and installing the new ane.
Though replacing an existing garbage disposal with a new one is a relatively piece of cake task, installing a disposal where in that location wasn't i before requires both plumbing and electric skills.
Starting from scratch is something you should tackle only if yous are an experienced do-it-yourselfer. Otherwise, hire an appliance installation pro. If you need help, you can go a referral from this free site: Call a pre-qualified local pro.
Earlier shopping for a new garbage disposal, please see our comprehensive Garbage Disposal Ownership Guide for helpful decision-making information.
Electric Requirements
When replacing an existing garbage disposal, you tin simply use the necessary electrical ability and switch that served the previous disposal.
A garbage disposal typically plugs into a 120-volt GFCI (ground-fault excursion interruptor) outlet under the sink. If an outlet like this isn't available under your sink, you lot'll have to have an electrician install one.
Be aware that most types of disposals crave a switch side by side to the sink to command the outlet—the electrician should wire for this, also. Notation: Batch-feed disposers don't require a switch considering they starting time when you insert and turn a special drain plug.
Instead of wiring a conventional electrical switch, a adept option is to buy an "air switch" for nigh $50.
Y'all can plug the disposal into this simple fiddling device so plug the air switch into an existing outlet. The garbage disposal is controlled by a modest push button that you lot tin mount nearby on the countertop or chiffonier. Another pick is to use a remote-control switch.
Selecting a New Disposal
If you buy a replacement that's made by the same manufacturer as your old model, you may exist able to bypass the need to replace the waste matter assembly and mounting flange in the sink, significantly simplifying the job (it can be a larger, more than powerful unit—it just needs to have the same mounting flange).
The more than powerful and quieter the garbage disposal you buy, the larger it volition be (for more about this, see Garbage Disposal Buying Guide). Make sure the i y'all intend to purchase will fit under your sink.
Preparing the Area
When replacing an old garbage disposal, start by unplugging it. If it's difficult-wired, shut off the power to the circuit that will serve the disposal before beginning whatsoever work and disconnect the wiring. Test the bare ends of the wires with an electrical voltage tester to brand sure they are not charged (run across How to Test an Electrical Excursion).
To provide ameliorate access and make your work easier, yous may be able to temporarily remove the cabinet doors under the sink, depending on their construction.
When working under the sink, article of clothing safety glasses, especially when you need to lay on your back looking up.
Accept a bucket or bowl and some rags ready to grab drain h2o when yous disconnect the drains.
You'll also need standard and Phillips screwdrivers, a hammer, a pipe wrench or locking-jaw pliers, and plumber'south putty.
Preparing the Garbage Disposer
Organize the components of your new garbage disposal on the countertop or floor.
You'll have the disposer unit, the sink-mounting assembly, an L-shaped tailpipe with mounting hardware, the sink stopper, and—with some brands—a special hex "wrenchette" that is used both for mounting the unit of measurement and for inserting into a hex hole in the disposer's underside when repair is needed to pause gratuitous clogs.
Yous'll need a power string, which you can usually remove from the sometime disposal and reuse. Be certain to read the manufacturer's installation instructions.
1 Attach the tailpiece to the disposal unit of measurement. The model shown here is attached with a round flange and a single spiral.
2 If your existing garbage disposal has a dishwasher hose fastened to it (this is commonly the instance if you have both a dishwasher and a disposal), you'll need to remove the dishwasher plug from inside the new disposal's dishwasher bleed nipple. Only exercise this if you'll be attaching a dishwasher!
Button the tip of a screwdriver upwardly confronting the edge of the plug and tap until you break loose the plug. Then remove this plastic disc from inside the disposal (you can probably concord the unit upside down and shake it out).
3 If your disposal doesn't have a cablevision clamp, screw one into the base of the disposer unit to secure the electrical cord. Unscrew the embrace from the disposer'southward electrical compartment.
Thread the electrical cord through the cable clench and into the disposal'south electrical compartment, and pull about two inches of the string through the opening. Earlier you tin can actually adhere the power cord to the unit, you'll need to remove the old disposal from nether the sink.
Removing the Sometime Disposer
Under the sink, place a bucket or pan below the waste pipe, so utilize locking-jaw pliers or a pipage wrench to disconnect the old disposal's tailpiece from the drain line'southward waste pipe. To loosen the nut, turn information technology counterclockwise.
Too remove the clamp or clip that secures the dishwasher's bleed hose to the disposal'due south dishwasher nipple and pull off the bleed hose.
At the top of the old disposer, put a screwdriver or the "wrenchette" into the right side of one of the lugs in the mounting ring. While holding the bottom of the disposal with the other hand, rotate the mounting ring counterclockwise to release the disposal. Be aware that the disposal may comprise water and food waste matter, and so carry it outside right-side up.
Then plow it over and, using a screwdriver, loosen the cable clamps that secure the cord, open the electrical compartment, disconnect the wire nuts and the cord from the disposal'due south wires, and remove the cord.
Installing the New Disposer
Now you tin can attach the ability cord to the new disposal. Strip 1/2-inch of insulation from the ends of the electrical cord's wires. Secure the grounding wire (usually green) by the light-green grounding screw. So twist together the bare ends of the cord'due south black wire and the disposer'southward black wire and secure with a wire nut. Then do the same with the white wires. Push the wires inside the compartment and spiral the embrace plate in identify.
If your disposal's installation volition require a new mounting flange in the sink, you'll need to install that start. If you're replacing an quondam disposer, remove it as discussed above.
Otherwise, put a basin or saucepan under the drain trap and detach and remove the drain piping that connects to the underside of the drain handbasket.
Remove the drain basket by unscrewing the large retaining nut that secures it (you'll need very large locking-jaw pliers to grip this), turning counterclockwise.
1 From in a higher place, make clean the area effectually the sink hole, and then utilize a gyre of plumber's putty around the perimeter. Push button the sink flange down into the pigsty, embedded it securely in the plumber's putty.
2 From below, place the washers and gaskets according to the manufacturer's directions. Slip the mounting ring onto the flange then slide on the snap ring until it snaps into identify. As tighten the iii mounting bolts, sealing the flange tightly against the sink. Remove excess plumber's putty.
3 Elevator upwards the new disposer under the mounting ring and marshal the mounting tabs below the entry points in the mounting tracks. Turn the band to engage the tabs so they lock onto the ridges. Use the "wrenchette" or a screwdriver to tighten the connectedness.
Rotate the disposal unit to marshal the discharge tailpiece with the bleed trap, and then connect it. Depending upon the existing trap configuration, yous may need to replace some or all of the bleed pipage beneath the sink to arrange the disposal.
4 Using a band clamp or retaining bound, connect the dishwasher drain hose to the disposal'southward dishwasher connection nipple (be sure you've removed the plug, as discussed above in Preparing a New Disposal).
5 Finally, plug the power cord into a GFCI-protected electric outlet that is continued to a switch (or hard-wire it to an electrical box). If needed, buy and install an air switch or remote-control module.
Here is a helpful video from Dan The Plumber, showing how to install a new garbage disposal:
Featured Resource: Notice a Local Garbage Disposal Installation Pro
Call for gratuitous estimates from local apparatus pros now:
1-866-342-3263
DOWNLOAD HERE
Minecraft How to Make a Garbage Disposal TUTORIAL
Posted by: joebesen1978.blogspot.com
Comments
Post a Comment